Top 10 Best 6×9 Speakers in 2020 – Reviews

In many ways, these Rockford speakers are the best you can get from the market at the moment. They have fantastic sound with their 91 dB sensitivity, and 75 watts of RMS power. The speakers are constructed using butyl rubber surround, PEI dome tweeter, a FlexFit basket design, and a mineral-filled and polypropylene injection molded cone.

But maybe the secret to these speaker’s top position in this speaker niche is that they have the VAST (Vertical Attach Surround Technique) Surround feature, which is able to improve the effectiveness of the radiating cone by 25%. Whatever the case, this is without a doubt the favorite 6 by 9 speaker in the market right now among many users.

Can’t Find What You’re Looking For? Check these suggestions:

Choosing the Best New Speakers

When you’re searching for new 6×9 speakers, there are a few things to keep in mind to get the best performing speakers possible. You need to keep in mind the size of the speakers, their sensitivity, their power handling capability and the build quality of the unit. That isn’t the only considerations that have to be kept in mind, however. The user also has to decide between component or coaxial speakers.

The component versus coaxial debate is one that’s been raging for years now. Component speakers offer the best sound quality but they’re usually way more expensive than coaxial speakers. On the other hand, coaxial speakers are usually the easiest ones to install and are harder to mess up if you’re doing a DIY install and don’t have a lot of experience installing speakers. Of course, the ultimate decision is up to you and will depend on your skill set, the ease of the install and your expectations.

How to Install Rear Car Speakers

Once you’ve found the best 6×9 car speakers and received them, it’s time to install them. While some people will always prefer having a professional install the speakers for them, other people like to take things into their own hands and install the speakers themselves. If you fall in the latter category, then put on your seat belt because we’re going to go over how to install them.

While this is only a general guide, and installation will vary from vehicle to vehicle, it will give most people a general overview of the process involved. Since this process is only a general overview and isn’t exactly a step-by-step guide, it’s always important to read your speaker’s instructions thoroughly before beginning this project.

What You’ll Need

Before you begin, there are a few items that you should gather together. Obviously, you are going to need the 6-inch by 9-inch rear speakers, but you are also going to need a speaker template. Some of the better 6×9 speakers come with a template included with them, but if your particular speak doesn’t, then you’re going to have to make one.

There are two ways you can do this: you can either use your speaker to make your own template, or you can find a website that has templates and download them to be printed out. The rest of the following tools needed for this job should be self-explanatory.

  • Cutting tool with grinding wheel
  • Cutting wheels
  • Cordless drill
  • 1/8-inch drill bit
  • Mounting screws
  • Gasket material
  • 3/8-inch ratchet
  • 12-mm socket
  • Flathead screwdriver
  • Safety glasses
  • Dust mask
  • Ear protection
  • Sharpie

Step One: Disconnect Your Battery

For safety purposes, you should always disconnect your battery when you’re removing old speakers and installing new ones. This can easily be done by just removing the negative cable off of the terminal while you’re working on the vehicle.

  Step Two: Removing the Factory Installed Speakers

Remove the speaker grills for the factory-installed speakers using your thumb. If necessary, you can also use your screwdriver to pop up this grill, but be careful because it’s extremely easy to damage the grill using a screwdriver. Once you have removed the factory speaker’s grill, unscrew the mounting screws from the speaker, pull it out and disconnect it from its connector.

  Step Three: Trace Out Your Template

Place your template over where the old speaker was and use your sharpie to trace the outline of your template into the installation that’s in the hole. Make sure that the center hole of the template lines up with where you think the center hole of the speaker should be located.

  Step Four: Cutting Out a Hole

While you’re wearing your dust mask, safety glasses, and earplugs, you can then begin cutting out the hole for your speaker. Take your cutting tool and use it to cut out the template outline you marked on the insulation fabric in the earlier step.

Once the material has been cut, you can then get rid of the material that’s been cut out. Making sure that you don’t deviate from your cutout too much, cut along the stock mounting tabs.

  Step Five: Smooth Out the Opening

Once you have cut out the hole for your speaker, you’ll probably need to clean up the edges of the hole. You can do this by using your Dremel with a grinding wheel to smooth out the edges of the opening.

  Step Six: Do a Test Speaker Insertion

Place your speaker into the hole you just made and examine it. Are there edges where the insulation is still in the way? If there is still excess material, then you will need to remove it. Does the speaker fit properly? If it doesn’t, then you will need to make adjustments as needed.

  Step Seven: Install the Speaker Gasket

Once you’re sure that the speaker fits perfectly, it’s now time to take the speaker out and install the gasket. The gasket wraps around the frame of the speaker and prevents the speaker from rattling against the cutout hole.

  Step Eight: Mount Your Speaker

Using the speaker’s mounting positions as a guide, go ahead and drill out each mounting screw hole and then connect the speaker wire connection to the speaker. Now install the speaker in the hole and tighten it down. When that’s been done to your satisfaction, place the grill cover back on your speaker.

  Step Nine: Reconnect Your Battery

Now all that has to be done is to reconnect the battery and test out your new speaker.

In Conclusion

Replacing your old 6×9-inch car speakers doesn’t have to be a big deal, as you can clearly see. With a little bit of planning and the proper tools, just about anyone can install or replace their new speakers.

Which makes you wonder why so many people decide to put up with the flat, dull factory-installed stock speakers that came with their car when they can revolutionize their listening experience with jazzy new speakers.

Leave a Comment

Your email address will not be published. Required fields are marked *

Want me to write short stories about your recipes?

I would Love to. Just send me a message.

Subscribe for newsletter

Join Our 203,849 Subscribers

A peep at some distant orb has power to raise and purify our thoughts like a strain of sacred music, or a noble picture, or a passage from the grander poets. It always does one good.

I only send really good stuff occasionally. Promise.

Scroll to Top